L&T PLACEMENT PAPER (TECHNICAL & APTITUDE)

Started by devi.naga, Dec 27, 2012, 09:14 PM

previous topic - next topic
Go Down

devi.naga

LnT  PLACEMENT PAPER (TECHNICAL & APTITUDE)

Aptitude:

Q1. Cost of an item is x. It's value increases by p% and decreases by p% Now the new value is 1 rupee, what is the actual value ?
 
Ans.(1000)/(1000-p*p).
 
Q2. A right circular cylinder and a cone are there. Base radius of cone is equal to radius of cylinder. What is the ratio of height to slant side if their volume are the same?
 
Q3. Distance between two poles is 50 meters. A train goes by 48 at a speed of kmph. In one minute how many poles will be crossed by the train ?
 
Q4. A pole seen from a certain distance at an angle of 15 degrees and 100 meters ahead by 30 degrees. What is the height of pole ?
 
Q5. For 15 people--each has to pay Rs.20.For 20 people--each has to pay Rs.18. For 40 people--how much has each to pay ?

Q6. If p=2q then q=r*r , if p-odd then q is even, whether r is even or odd ?
a) first condition is sufficient
b) second condition is sufficient
c) both are sufficient
d) both are not sufficient
 
Q7. If A occurs which of the following must occurs
I. F & G
II. E and H
III. D
 
(a) I only
(b) II only
(c) III only
(d) I, II, III
(e) I, II (or) II, III but not both
 
Ans. (e)
 
  Q8. If B occurs which must occur
 
(a) D
(b) D and G
(c) G and H
(d) F and G
(e) J
 
Ans. (a)
 
 
Q9. If J occurs which must have occurred
 
(a) E
(b) either B or C
(c) both E F
(d) B
(e) both B and C
 
Ans. (b)
 
Technical:
 
Q1. What is the ideal op-amp CMRR ?
 
Ans. infinity.
 
  Q2.For a 13-bit DAC the MSB resistance is 2kohms. What is the LSB resistance ?
 
Ans. 2kohms * 2 12
 
Q3. The layer in the OST model handles terminal emulation
a) session
b) application
c) presentation
d) transport
 
Ans. (b)
 
  Q4. Long int size is
a) 4 bytes
b) 2 bytes
c) compiler dependent
d) 8 bytes
 
Ans. (c)
 

Q5. Find the output of
x=2,y=6,z=6
x=y=z;
printf("%d",x);
 
 
Q6. FTP is carried out in ___________ layer ?
 
7. in diesel engine the comp. ratio is ______ then expansion ratio(more,equal,less,...)

8 . carbon help in the improving __ of steel(ductility,malliability,hardness,machinability)
 
9. pig iron is manufacture in --------blast farness
 
10. what is the effect of increase arc lenght in building
 
11. m 62 indicates ------ 6mm outer diameter & 2 mm pitch
 
12. what rapture failure.

13 . 6 cylinders in a row , n0. of crancks = 1
 
14. If in a steam power plant vacuum in condenser reduces what is the effect
 
15. pressure in industrial pneumatic lines -------5 to 10 bar
 
16. effect of low temp. ( -20 degree ) on carbon steel .
 
17.method of hardening of machine guides ways
 
18. method of joining plastic by welding
 
19. safe method of loading on a cantilever
 
a) UDL  b) center point load  c) triangular load having zero at center
 
20. BMD for UDL in cantilever
 
Ans. parabolic

Go Up
 

Quick Reply

With Quick-Reply you can write a post when viewing a topic without loading a new page. You can still use bulletin board code and smileys as you would in a normal post.

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.
Name:
Email:
Verification:
Please leave this box empty:

Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:

shortcuts: alt+s submit/post or alt+p preview
IT Acumens Web Design Chennai | GinGly :: Mobile SMS Backup | CineBuzz :: Latest Cinema News | My Kids Diary :: Kids magical moment :: Book domain name @ 99 Rs monthly
Copyright 2005 - 2019 :: IT Acumens :: All Rights Reserved.
ITAcumens Forum with 2 lakhs post running for 14 years - Powered by IT Acumens Dedicated Server