Author Topic: MicroProcessor Interview Questions - Part 2  (Read 4534 times)

magesh.p

  • Acumen Magesh
  • Senior Acumen
  • Hero Member
  • ***
  • Posts: 1475
  • Love to be an Acumen
    • View Profile
    • IT Acumens
MicroProcessor Interview Questions - Part 2
« on: March 27, 2008, 03:38:13 pm »
MicroProcessor Interview Questions

What is the difference between 8086 and 8088?

The BIU in 8088 is 8-bit data bus & 16- bit in 8086.Instruction queue is 4 byte long in 8088and 6 byte in 8086.

Give example for Non-Maskable interrupts?

Trap is known as Non-Maskable interrupts, which is used in emergency condition.

Give examples for Micro controller?

Z80, Intel MSC51 &96, Motorola are the best examples of Microcontroller.

What is clock frequency for 8085?

3 MHz is the maximum clock frequency for 8085.

Give an example of one address microprocessor?

8085 is a one address microprocessor.

Give examples for 8 / 16 / 32 bit Microprocessor?

8-bit Processor - 8085 / Z80 / 6800; 16-bit Processor - 8086 / 68000 / Z8000; 32-bit Processor - 80386 / 80486

What is meant by a bus?

A bus is a group of conducting lines that carriers data, address, & control signals.

What are the various registers in 8085?

Accumulator register, Temporary register, Instruction register, Stack Pointer, Program Counter are the various registers in 8085

Why crystal is a preferred clock source?

Because of high stability, large Q (Quality Factor) & the frequency that doesn’t drift with aging. Crystal is used as a clock source most of the times.

In 8085 which is called as High order / Low order Register?

Flag is called as Low order register & Accumulator is called as High order Register.

Name 5 different addressing modes?

Immediate, Direct, Register, Register indirect, Implied addressing modes

In what way interrupts are classified in 8085?

In 8085 the interrupts are classified as Hardware and Software interrupts.

What is the difference between primary & secondary storage device?

In primary storage device the storage capacity is limited. It has a volatile memory. In secondary storage device the storage capacity is larger. It is a nonvolatile memory. Primary devices are: RAM / ROM. Secondary devices are: Floppy disc / Hard disk.

Which Stack is used in 8085?

LIFO (Last In First Out) stack is used in 8085.In this type of Stack the last stored information can be retrieved first.

What is Program counter?

Program counter holds the address of either the first byte of the next instruction to be fetched for execution or the address of the next byte of a multi byte instruction, which has not been completely fetched. In both the cases it gets incremented automatically one by one as the instruction bytes get fetched. Also Program register keeps the address of the next instruction.

What is the RST for the TRAP?

RST 4.5 is called as TRAP.

What are level-triggering interrupt?

RST 6.5 & RST 5.5 are level-triggering interrupts.

Which interrupt is not level-sensitive in 8085?

RST 7.5 is a raising edge-triggering interrupt.

What are Software interrupts?

RST0, RST1, RST2, RST3, RST4, RST5, RST6, RST7.

What are the various flags used in 8085?

Sign flag, Zero flag, Auxiliary flag, Parity flag, Carry flag.

In 8085 name the 16 bit registers?

Stack pointer and Program counter all have 16 bits.

What is Stack Pointer?

Stack pointer is a special purpose 16-bit register in the Microprocessor, which holds the address of the top of the stack.

What happens when HLT instruction is executed in processor?

The Micro Processor enters into Halt-State and the buses are tri-stated.

What does Quality factor mean?

The Quality factor is also defined, as Q. So it is a number, which reflects the lossness of a circuit. Higher the Q, the lower are the losses.

How many interrupts are there in 8085?

There are 12 interrupts in 8085.

What is Tri-state logic?

Three Logic Levels are used and they are High, Low, High impedance state. The high and low are normal logic levels & high impedance state is electrical open circuit conditions. Tri-state logic has a third line called enable line.

Which interrupt has the highest priority?

TRAP has the highest priority

What are Hardware interrupts?

TRAP, RST7.5, RST6.5, RST5.5, INTR

Can an RC circuit be used as clock source for 8085?

Yes, it can be used, if an accurate clock frequency is not required. Also, the component cost is low compared to LC or Crystal
- An Proud Acumen -

Upload your Resume here, A copy will be sent to IT Acumens & Team.
And we will directly Refer to top companies.

To Learn about our openings & Training,
please send your resume indicating desired position to career@itacumens.com (or)
Type "JOIN JOB" and Send
SMS to 9566295662 For Free Job Openings.
Type "JOIN TRAIN" and Send SMS to 9566295662 For Free Training Information's.